High Speed Box Beam Production Line, Automatic Steel Coil Slitting Machine

1. Technical parameters

a. Application: Cold steel sheet, Galvanized coils

b. Tensile strength: b≤400Mpa

c. Coil weight: 15T

d. Thickness: 0.4-4 mm

e. Width of coil material: 1600mm

f. Coil I.D: φ508

g. Coil O.D: φ1600mm

h. Line speed: 0-100m/min (0.4-1mm), 0-80m/min (1-2mm), 0-70m/min (2-4mm)

i. The diameter of slitting blade shaft: φ220

j. Slitting blade: φ220*φ360*20

k. Material of slitting blade: 6CrW2Si

l. The hardness of slitting blade: HRC58°-60°

m. Recoiler I.D of scrap winder: φ420

n. Recoiler I.D: φ508mm

o. Tolerance of width error: ≤±0.05mm

p. Other parameters:

    power: 380V/50Hz/3Ph

    area of the whole machine: 26m (L) * 8m (W)

    operator needed: 1 technician and 2 general workers

    weight of the whole machine: 40T

2. Composed devices

a. Hydraulic entry coil car

b. Hydraulic de-coiler

c. Hydraulic press and guide and pinch device

d. Hydraulic head-cutting machine

e. Looper I

f. Guide device

g. Slitting machine

h. Scrap winder

i. Looper II

j. Hydraulic damping and pre-dividing and press device

k. Recoiler

l. Hydraulic exit coil car

m. Hydraulic system

n. pneumatic system

o. Electric control system

3. Description of the whole machine line

        ZJX-4*1600mm steel coil slitting line is used for slitting the carbon plate to prepare for the next process.

a. Hydraulic entry coil car

    The car can move levelly and vertically, which is convenient for putting the steel coils into the de-coiler

    It is driven vertically by hydraulic cylinder with four guide pillars

    The level movement is driven by cycloid motor

b. Hydraulic un-coiler

    Supporting steel rolls and uncoiling

    It can expand and shrink with hydraulic oil cylinder and fit with the inner hole of the steel coils and is equipped with supporting stand

    Moment motor drives the coils running and the motor can run right and left to prevent the coils running by inertia

c. Press and pinch and feed device

    It is good for improve the plates' surface and do straightening then guiding the steel plates into next process

    It is made by 5 leveling rollers, drive device, 2 pinch roller and frame. Every rollers is the main driving rollers

    The gap between rollers can be adjusted manually to make sure the leveling quality

    hydraulic telescopic shovel and hydraulic press and hit the head device etc. to feed the plate

    Drive model: all the rollers and gear box drives by 30 KW motor

d. Hydraulic head-cutting machine

    Adopt two columns structures, a press device, can cut the 4mmX1600 steel plates

    The up and down blades which are alloy material 6CrW2Si can adjust their gap

    The machine is used for the steel shear and to make the plate easy to slitting machine

e. Looper I

    It uses the 2 groups of magic eyes to control the speed buffer between decoiler and slitting machines

    The looper will create a buffer zone for easier into next stage process

f. Guide device

    On both sides of the mixer used vertical roller wheel device, lead the steel strip right into slitting host

    Pieces on both sides of guide bit screw adjustment on both ends of the vertical roll by, the width of the range: 500-1300mm

    Set the two roller material damping device, improve the accuracy of slitting

g. Slitting machine

    Power part: This is composed of power-stand, decelerator, 55KW direct current motor, gear distributing case, coupler, spindle, connecting-cover, etc.

    Host machine: This is composed of bottom-stand, fixed bracket, big slide, knife pivot(φ220mm, 2pcs), movable bracket, slide, the front and back adjustable device of bracket, knife pivot lifting and pressing down adjustment device, accompany of  blade, separating cover, rubber band and 20 blades with the machine

    It change the blades through moving out the bracket hydraulically and is very convenient and fast

h. Scrap winder

    It consists of base, the shaft and plate of scrap material, friction wheel, supporting wheel chain, chain, decelerator and 7.5Kw electric machine

i. Looper II

    It is equipped with the bridges which is driven by hydraulic. When feeding the head of the coils, the bridge can lift up and be a surface to make the plate easy into next progress, once finished the feeding period, the bridge will lift down to create the buffer zone to store enough plates and ensure the recoiling quality

j. Tension stand

    It consists of the frame, pre-dividing device, press and tension device and guide rollers and so on. And it is used to adjust the tension of pre-divide and recoiler to make sure the even and tight quality

k. Recoiler

    It adopts the hydraulic expand and shrink recoiler shaft to tight the inner hole of coils

    it uses the hydraulic movable arm with the supporting spacers to ensure the even recoiling quality

    It is equipped with the push device to help unload the coils

 Mr. Louis

Tel: 86-755-86090339

Contact to this supplier